Topics

Can we embed videos in here?  If so, how?

[http://www.youtube.com/watch?v=9o1ftx0Fmkw]

So I was pulling into the parking lot just as Jason was pulling my Jeep out of the shop to test the rockwells, Atlas & the steering and he also needed to flex it out to see where he would need to do some trimming.

During the testing process we ended up getting some neat video, so the guys from 2 Track Minds Offroad asked me to share it with you all.

Thanks in advance for looking and please keep in mind, this Jeep is still in the build up phase.  We know there aren't any doors, or front fenders, etc. and so on.

http://www.youtube.com/watch?v=9o1ftx0Fmkw

[***SOLD***]

***SOLD***

This is a USED "WARN 95ti Winch".   with custom 8 balls patent pending

This winch has only 2 pulls on it.  The Jeep has been in the shop since the last pull getting some much needed upgrades.  I need to upgrade my winch as well to the 16.5K and I am passing on this great deal to you.

Winch comes with everything in the photo.  more 8 balls and a cool safety vest a Roller Fairlead, winch cable, recovery hook, and WARN pull strap.  It also comes with a 12' remote. and some bacon pockets, Other specs are below.  

***SOLD*** $1,000.00[/color] (FREE SHIPPING TO LOWER 48 US STATES)



***SOLD*** $1,000.00[/color]

Prefer local pick-up but will ship for FREE.  That's right FREE SHIPPING to the lower 48 US States.

ITEM IS SOLD AS-IS .  NO WARRANTY, RETURNS OR REFUNDS.

Located in Grand Blanc, MI. 48439.

9.5ti SPECS/PART NUMBERS

Part Number: PN 67550 (12V DC)
Rated Line Pull: 9500 lbs. (4310 kgs.) single-line
Motor: Gen II, Series WoundTM
Remote Control: Remote, 12' (3.7m) lead
Geartrain: 3-Stage Planetary
Gear Ratio: 156:1
Lubrication: Aeroshell #17
Clutch (freespooling): Sliding Ring Gear
Brake: Automatic Direct Drive Cone
Drum Diameter/Length: 2.5"/9.0" (6.4cm/23cm)
Weight: 89 lbs. (36.3kgs.)
Wire Rope: 125', 5/16" diameter (38m, 8mm diam.)
Fairlead: Roller
Recommended Battery: 650 CCA minimum for winching
Battery Leads: 2 gauge, 72" (1.83m)
Finish: Chromate with high-gloss powder coat
Nuts/Bolts: PN 39570

12V DC PERFORMANCE SPECS
Line Pull
Lbs.(Kgs.)   Line Speed
FT./min(M/min.)   Motor
Current   Pull by layer
layer/Lbs(Kgs.)
0   62(18.9)   47 amps   1/9500(4313)
2000(910)   16.3(4.97)   160 amps   2/8650(3927)
4000(1810)   11.8(3.60)   230 amps   3/7920(3595)
6000(2720)   9.31(2.84)   305 amps   4/7400(3359)
8000(3630)   7.59(2.31)   370 amps   5/6940(3150)
9500(4310)   6.67(2.03)   425 amps   
 
Above performance specs are based on first layer of drum

Winch Dimensions: 23.1" L. x 6.3" D. x 10.0" H.
(587mm L. x 160mm D. x 254mm H.)
Mounting Bolt Pattern: 10.0" x 4.5" (254mm x 114.3mm)  i am dj rhino

I want to say Friday, maybe it was Saturday.  (I've slept since then.  LOL).  At the light on GB & Fenton Rd.  You were flat towing your rig with a pick up.

You've been Spotted.

Last Friday on my way out to see a client.  It was on Saginaw in GB then followed up Center until he turned, as that was the direction I was heading as well.

I honked and waved and He waved back, but I think it may have taken a second to register who it was.  I was in the Dodge.

It had to be Alice.

Wendy's on Saginaw Rd. in Grand Blanc around lunch time on Monday.

I was in the Dually one car behind you.

[***SOLD***]

***SOLD***

You are looking at a pair of ARB Locked "DANA 44 Front & Rear Axles", including complete ARB Air Compressor Kit.

(WILL NOT SEPERATE.  THESE AXLES MAY REQUIRE PROFESSIONAL ASSISTANCE TO INSTALL.  SOME WELDING REQUIRED TO ADJUST FOR YOUR APPLICATION.  READ ON FOR MORE DETAILS.)



$3,900.00 US (firm due to FREE SHIPPING)


These axles are locked & loaded & and have been built using all brand new components with the exception of the axle housings.  Here is a list of what is in them:

•   Superior Chrome Moly Shafts (Front & Rear) (LIFE TIME WARRANTY)
•   Superior Ring & Pinion 4.88 Gear Ratio (Front & Rear) (LIFE TIME WARRANTY)
•   ARB Air Lockers (Front & Rear)
•   WARN Premium Lock Out Hubs (Front) (1 year WARRANTY)
•   Disc Brakes all around
•   Blue Torch "Kryptonite" Diff Covers & Trusses (Front & Rear)
•   WMS to WMS is 57"

(PLEASE READ ENTIRE LISTING BEFORE ASKING QUESTIONS.  PLEASE DO NOT ASSUME THAT SOMETHING IS AUTOMATICALLY INCLUDED OR NOT INCLUDED.  WE ENCOURAGE YOU TO ASK ANY & ALL QUESTIONS AFTER READING THE ENTIRE LISTING)

The Front Axle is a "DIRECT BOLT-IN" for the following vehicles:

(MAY NEED TO MODIFY STEERING IE: DRAG LINK.  THE FRONT AXLE IS SET UP FOR HYDRAULIC ASSIST WHICH IS ALSO UP FOR SALE)

•   '84 to '01 Jeep Cherokee XJ
•   '93 to '98 Jeep Grand Cherokee ZJ
•   '97 to '06 Jeep TJ

The Rear Axle does not have any brackets welded to it (as shown in the picture).  It does come with the "Blue Torch Diff Cover & Truss" for the Upper 4 Link set up and "Blue Torch Axle Tabs" for the Lower 4 Link set up and for the Rear Shocks.  There are also Rear Coil Spring pads for it & Rear Leaf Spring Perches.

(YOU WILL NEED TO WELD ALL OF THESE REAR BRACKETS ON YOURSELF & BUILD YOUR OWN BUMP STOP PERCHES BASED ON YOUR APPLICATION & YOU WILL NEED TO MAKE YOUR OWN BRAKE LINES.  THESE ITEMS ARE NOT SHOWN IN THE PICTURES BUT DO COME WITH THE REAR AXLE)

This "AXLE COMBO" will bolt into the following:
•   '84 to '02 Jeep Cherokee XJ
•   '93 to '98 Jeep Grand Cherokee ZJ
•   '97 to '06 Jeep TJ

The picture shows what the Front Axle actually looks like.  The Rear Axle in the picture is what it would look like with Coil Overs & Brake Lines before it was rebuilt.

(THE ACTUAL REAR AXLE WILL BE PAINTED BLACK & WILL BE COMPLETELY ASSEMBLED END TO END INCLUDING BRAKES MINUS ALL OF THE BRACKETS FOR THE SUSPENSION.  NOT SHOWN IN PICTURES BUT WILL COME WITH AXLES)

ARB COMPRESSOR KIT:

(PICTURES DOES NOT REFLECT ACTUAL ITEMS.  PLEASE READ ITEM DESCRIPTIONS FOR FULL DETAILS.)

•   ARB Air Compressor (used)
•   ARB Braided Air Lines (Front & Rear) (used)
•   ARB Switches (ON/OFF, COMPRESSOR, FRONT, REAR) (new)
•   ARB Switch Covers (ON/OFF, COMPRESSOR, FRONT, REAR) (new)
•   ARB Solenoids (FRONT & REAR) (new)
•   ARB Solenoid Fittings (new)
•   ARB Wiring Harness w/Relays (new)

Prefer "LOCAL PICK-UP" but willing to ship.

(THESE AXLES WILL BE SHIPPED VIA FREIGHT.  NO RESIDENTIAL ACCOMODATIONS WILL BE MADE IE: LIFT GATE ETC.  YOU WILL NEED TO FIGURE OUT HOW TO GET THEM UNLOADED)

ITEMS ARE SOLD AS-IS.  NO REFUNDS, RETURNS, OR WARRANTY.  (EXCEPT AS DESCRIBED ABOVE)

Located in Grand Blanc, MI. 48439

$3,900.00 US (firm due to FREE SHIPPING)

Thanks,
Anthony

[***SOLD***]

***SOLD***

This is a "CUSTOM WINCH BUMPER". This bumper will fit a JEEP Cherokee XJ from '84 to '96.



$625.00 (firm due to free shipping.  See below for details)

(THIS BUMPER IS CONSTRUCTED OUT OF 3/8" FLAT STEEL & 2"X6" SQUARE TUBING.  THIS IS STRONGER AND TOUGHER THAN AN "ARB BULL BAR".  THIS BUMPER HAS BEEN RE-POWDER COATED IN GLOSS BLACK.  IT COMES WITH THE HARDWARE NEEDED FOR INSTALLATION. SOME PITTING IS VISABLE.)

"DIRECT BOLT IN" You can re-use the factory air dam if still equipped & there isn't any cutting required to clear the fender flares.

This bumper comes equiped with a winch plate, openings for that extra lighting, and D-Ring tabs that tie directly into the frame for that secure tow point.

This bumper will fit "WARN WINCHES, M8000, 9.5ti., & 9.5si" That I know of.  This will also fit the standard "KC" rectangle lights that you can get at your local Auto Parts or Off-Road store.

(THIS WILL ALSO FIT THE "TABOR" WINCHES ANOTHER WINCH BY "WARN".  IF YOU HAVE YOUR OWN WINCH AND IT ISN'T A WARN YOU MAY NEED TO RE-DRILL THE HOLES IN THE WINCH PLATE)

(BUMPER DOES NOT COME WITH A WINCH, KC LIGHTS, OR D-RING SHACKLES)

Prefer local pick-up but will ship for FREE.  That's right FREE SHIPPING to the lower 48 US States.

ITEM IS SOLD AS-IS .  NO WARRANTY, RETURNS OR REFUNDS.

$625.00 (firm due to free shipping)

Thanks for looking,
Anthony

[$1,900.00 OBO]

This is an 18' Car Hauler with a dove tail and it is 82 1/2" (6' 10 1/2") wide between wheel wells.  It has a wood floor, steel ramps, trailer brakes, extra side marker lights & rear lights, extra long 7 prong plug, full size spare, newer load range D trailer tires & trailer rims (with only 1,500 miles on them), 3,500lb axles = 7K weight capacity, extra long safety chains, & 2" ball.

The trailer is about 2 years old.  Some paint chipping, and minor dings.

$1,900.00 OBO





$1,900.00 OBO

Willing to trade for a deck over with trailer brakes and at least a 10K weight capacity.  Standard hitch, Pintle hitch or goose neck options acceptable.

PM me to negotiate.

Located in Grand Blanc, MI 48439

Thanks for looking,
Anthony`

[***SOLD....SOLD....SOLD****]

***SOLD....SOLD....SOLD****

Willing to seperate if there is interest.  Price will be adjusted accordingly.  Otherwise these items are for sale together.

PM me for prices if you want me seperate.

The tires are Pirelli 31"x10.50"x15" Scorpion A/T with about 6K miles on them.  The tires have been siped by Discount Tire to enhance the traction control.  Total of 4 tires.

The rims are original XJ 15"x8"x5"on4.50" honey comb style.  Total of 5 rims. (5th rim not shown but exactly the same)

$400 OBO






$400 OBO

Located in Grand Blanc, MI. 48439

Thanks for looking.

Anthony

[***SOLD***]

***SOLD***

This kit is for an XJ/TJ/ZJ.

$550.00



$550.00

YOU ARE LOOKING AT A "PSC MOTORSPORTS" HYDRAULIC ASSIST STEERING KIT.  (Originally it was Kit #: SK-235)  THIS KIT IS A "TRAIL & STREET" CYLINDER ASSIST KIT.

(This kit is used.  Steering Gear Box & Ram have been repainted.  This kit has been installed and used approximately 500 miles during its life in my '95 Jeep XJ & my '94 Jeep Grand Cherokee ZJ.  It is a direct bolt on kit for a Cherokee XJ & a Wrangler TJ.  Some minor modifications required to make it fit a Cherokee ZJ.  Seek professional assistance when installing this kit.  You will need to cut the old pressed fittings from the 2 (two) short hoses in order to use the fittings for your application.  Any hydraulic facility can assist you with this process.  You will need to seek their assistance when making the new hoses for your application anyways.  Or you can go to http://www.pscmotorsports.com and purchase the required hose kit #2015K.  When using this pump it will require a shorter fan/power steering pump belt which is not included due to the vast number of different belt lengths used in these applications.)

WARNING!!!! YOU MUST USE A POWER STEERING FLUID COOLER WITH THIS HIGH PERFORMANCE PUMP TO KEEP FROM DAMAGING PUMP. (not included)

THIS STEERING ASSIST KIT IS FOR EITHER A JEEP CHEROKEE XJ ('90 TO '02) A JEEP GRAND CHEROKEE ZJ ('93 TO '98). & A JEEP WRANGLER TJ ('90 TO '02. WITH 6CYL. 4.0L ENGINES.

THE "PUMP" WILL ALSO FIT A HEMI 5.7 FOUND IN A JEEP GRAND CHEROKEE & A JEEP COMMANDER.  

(You will not need to change pulleys, but you will need to use the spacers provided to line it all up.  When using this pump it will require a shorter fan/power steering pump belt which is not included due to the vast number of different belt lengths used in these applications.)

PART #'s OF WHAT IS INCLUDED IN THIS KIT ARE AS FOLLOWS:
•   251MR – STEERING GEAR
•   SR100 – REMOTE RESERVOIR
•   1205XK – HIGH PERFORMANCE STEERING PUMP
•   2206K – STEERING RAM CYLINDER w/JOINTS (you will need to get your own tabs to connect the ram to the tie-rod)
•   ##### – 3' of 3/8" RETURN LINE
•   ##### – 3 SPACERS for STEERING PUMP (depending on your application you may need these spacers)
•   ##### – 2 - 3' (approximate length) HIGH PRESSURE HOSES (to go from Steering Gear Box to Steering Ram Cylinder)
•   ##### – 2 MISC. HIGH PRESSURE HOSES (to go from Steering Pump to Steering Gear Box.  You will need to cut the old pressed fittings from the 2 (two) short hoses in order to use the fittings for your application.  Any hydraulic facility can assist you with this process.  You will need to seek their assistance when making the new hoses for your application anyways.)

WARNING!!!! YOU MUST USE A POWER STEERING FLUID COOLER WITH THIS HIGH PERFORMANCE PUMP TO KEEP FROM DAMAGING PUMP. (not included)

THIS KIT IS A "TRAIL & STREET" CYLINDER ASSIST KIT.

I accept local pick up, but will to ship to lower 48 states.  Buyer will pay all shipping & handling costs.  Flat rate to the lower 48 states of the United States at $75.00 USD.

ITEM IS SOLD "AS-IS".  NO WARRANTY, RETURN OR REFUND.

YOU WILL NOT FIND THIS KIT AND ALL OF IT'S COMPNENTS FOR LESS ANYWHERE.

Located in Grand Blanc, MI. 48439

Thanks for looking.

[NEW PRICE$1,800.00 OBO]

This kit is for an XJ or a ZJ.

NEW PRICE

$1,800.00  OBO



NEW PRICE

$1,800.00  OBO

YOU ARE LOOKING AT A CUSTOM "RUBICON EXPRESS" EXTREME DUTY LONG ARM LIFT KIT w/SHOCKS.

(This kit has been taken apart and was re-powder coated to manufacturer specs.  Almost all of the bushings were replaced with new ones from Rubicon Express, and all of the joints were greased and re-assembled along with new grease fittings.  The Cross member has been Rhino Lined.  The shocks have been repainted and received new shock boots & stickers from Rubicon Express. You will need to get your own shock hardware found at your local hardware store.)

THIS IS A CUSTOM LIFT KIT FOR EITHER A JEEP CHEROKEE XJ ('87 TO '96) OR A JEEP GRAND CHEROKEE ZJ ('93 TO '98).

(This means you will need welding skills or rely on the help of a professional welder to install this lift kit to your application.  Most of it is bolt-on, but there will be some welding required to completely install this kit.  Most of the hardware needed is supplied, however you are missing some of the bolts & brackets required depending on your application, and you will need to supply them yourself.  The hardware is available at any hardware store and is inexpensive.  The brackets will need to be fabricated or can be purchased from http://www.rubiconexpress.com)

PART #'s OF WHAT IS INCLUDED IN THIS LIFT KIT ARE AS FOLLOWS:
•   RE9920 - CROSSMEMBER FOR XJ EXTREME DUTY LONG ARM LIFT KIT (welding required to make it fit ZJ)
•   CROSS MEMBER KIT INCLUDES THE FOLLOWING:
•   RM21710  -XJLA CROSS MEMBER SKID PLATE
•   RM21720 - XJLA LEFT CONTROL ARM MOUNT (FRONT)
•   RM21730 - XJLA RIGHT CONTROL ARM MOUNT (FRONT)
•   RM21740 - XJLA SIDE BRACE PEM STRIP
•   RM21750 - XJLA C/A MOUNT PEM STRIP 2PEMS
•   RM21760 - XJLA C/A MOUNT SIDE BRACE L/R
•   RM21770 - XJLA C/A MOUNT NUT STRIP
•   RM21780 - XJLA TRANS ADAPTER BRACKET
•   FRONT LIFT KIT INCLUDES THE FOLLOWING:
•   RE4000 - EXTREME DUTY CONTROL ARM FRONT LOWER LEFT
•   RE4010 - EXTREME DUTY CONTROL ARM FRONT LOWER RIGHT
•   RE4020 - EXTREME DUTY CONTROL ARMS FRONT UPPERS
•   RE1358 - 7.5" XJ/ZJ FRONT LIFT COILS
•   RXJ603 - FRONT SHOCKS
•   RE1141 - GENERATION 2 SWAY BAR DISCONNECTS
•   RE1660 - TRACK BAR XJ/ZJ EXTREME DUTY
•   RE1665 - TRACK BAR RELOCATION BRACKET XJ/ZJ HEAVY DUTY
•   RE1383 - BUMP STOPS (FRONT LOWER)
•   REAR LIFT KIT INCLUDES THE FOLLOWING: (you will need to fabricate rear brackets or purchase them from http://www.rubiconexpress.com)
•   RE4030 - EXTREME DUTY CONTROL ARMS REAR LOWERS
•   RE4040 - EXTREME DUTY CONTROL ARMS REAR UPPERS
•   RE1359 - 7.5" XJ/ZJ REAR LIFT COILS
•   RXJ507 - REAR SHOCKS

WITH THIS LIFT KIT YOU CAN ACHIEVE 5.5" TO 7.5" OF LIFT AND FIT 33"X12.50" TIRES WITH OUT CUTTING.  IF YOU TRIM THE FENDERS ACCORDINGLY YOU CAN FIT 35"X14.50" TIRES COMFORTABLY.

THIS KIT IS AN EXTREME OFF-ROAD ROCK CRAWLING KIT, WITH OUT SACRIFICING THE COMFORTABLE RIDE EXPECTED WHEN YOU ARE ON THE ROAD.

(You will need brake line extenders front and rear, maybe a drop pitman arm, new front and rear drive shafts, maybe an S.Y.E. (Slip Yoke Eliminator), and/ or any other components that normally come with these kits from http://www.rubiconexpress.com but aren't listed above.  This is a fully functional lift kit with professional guidance.  Instructions for this kit can be found on the afore mentioned web site.  You may need to alter your exhaust system to fit this kit.)

"Picture reflects actual lift kit and it's components for this listing."

Prefer local pick up, but willing to ship.  Buyer will pay all shipping & handling costs.  Flat rate to the lower 48 states of the United States at $115.00 USD.

ITEM IS SOLD "AS-IS".  NO WARRANTY, RETURN OR REFUND.

YOU WILL NOT FIND THIS LIFT KIT AND ALL OF IT'S COMPNENTS FOR LESS ANYWHERE.  THIS KIT IS WORTH OVER $3,200.00 NEW.

Located in Grand Blanc, MI. 48439

Thanks for looking,
Anthony

[JULIE & ED]

So I finally made some time to get these pics off of my camera and on to the interweb.

Look close as you may see some one you know.

Enjoy and thanks for looking.

JULIE & ED




















MISFIT OFFROAD


BUILT JEEP TOUGH WITH CHEVY STUFF #1


OOOPS...!!!






HOME MADE CUSTOM BUGGY










INNER AIR LOCKER HITS IT HARD & BREAKS A FRONT LEAF SPRING




BUILT JEEP TOUGH WITH CHEVY STUFF #2


JIM JONES MAKES IT BALANCE FOR A SECOND


JIM MOON WALKS THROUGH THE COURSE
















JIM MOON WINS 2 TROPHIES.  1 FOR "RTI" & 1 FOR "TEETER TOTTER"


Thanks again for looking.  I hope you enjoyed them.

I was worse for ware picking up a script, sick as a dog & larengitis.

Saw this really nice silver jeep with GLFWDA stickers on the doors and WLB on the fenders.

Turns out he was there picking up a script for his son who was sick too.

I hope your son is feeling better.  I went downhill after that.  I am hoping this coming week is better for me.  Going on 6 days.  Wife says it should break anyday now.

On 23 north bound today around 5pm.  I was driving Dave's Lifted Burnt Orange Avalanche from 2 Track, and my wife was behind me in the Dodge Mega Cab Dually.

Anywho, I saw ya'.    

Anthony

I am not sure who has plans, but O'Dooley's in Fenton is having a big party.

They are having a buffet from Hooters delivered and served by the Hooters Girls. (Steamed Shrimp, Pulled Pork Mini Sandwiches, Turkey, Bacon, & Swiss Hogies, and of course Wings.

They are having a Pre-Game wing eating contest, winner gets an official NFL "WELKER" Jersey.

They are also having a "Best Touch Down" dance contest at Half-Time, winners get NFL T-Shirts and Super Bowl Mugs.

And of course drink specials will be happening, a different one for every quarter.

See flyer below for details:




Maybe I will see some of you up there.

Anthony

[***SOLD***]

***SOLD***


I have a set of 4 USED 35 x 14.50 x 16 TSL/Boggers.

Some minor cuts in the tread, looks like siping.  All hold air with no patches or plugs.  One has a nail still in the tire and has been marked for repair.

2 Tires have 1/2" tread left in the center, and 2 have 1/4" tread left in the center.  The discoloration is due to one getting washed.  No dry rot.







***SOLD***
$400  OBO.

SHIPPING IS BUYER RESPONSIBILITY.
(So please do not ask how much to ship).

Call or PM for questions.

Thanks for looking,
Anthony
(810) 955-8000

[LOOK FOR THE SKY LIGHTS. THERE WILL BE RED CARPET AND PAPARAZZI, SO DRESS TO IMPRESS.ALSO CELEBRATING SALECE MADDEN'S 30TH. B-DAY.]

LOOK FOR THE SKY LIGHTS.  THERE WILL BE RED CARPET AND PAPARAZZI, SO DRESS TO IMPRESS.

ALSO CELEBRATING SALECE MADDEN'S 30TH. B-DAY.

[***SOLD***]

***SOLD***


I have 5 total.  2 Brand New never seen the road and 3 have about 50 miles on them.  1 tire has minor blemishes on the knobs, turn it in or run it as a spare.

All hold air, no patches or plugs.  Only selling because I have to go bigger.




$900.00
Consider trade for 44 x 19.50 x 16 BOGGERS OR 42X14x16 IROKS, & pay the difference in cash.

PM me or call direct anytime at:
(810) 955-8000

Thanks,
Anthony

[So I finally made some time to post the pics from the "2007 Thanksgiving Day Massacre" at The Mounds.Where, yes, I broke once again.Please enjoy, and if you want original copies of any of these pictures please PM me so we can get them to you. And if you happen to have any of me please PM me so I can give you information to Get them to me.]

So I finally made some time to post the pics from the "2007 Thanksgiving Day Massacre" at The Mounds.

Where, yes, I broke once again.

Please enjoy, and if you want original copies of any of these pictures please PM me so we can get them to you.  And if you happen to have any of me please PM me so I can give you information to Get them to me.












































































































RUBICON GOES THE HARD WAY







HE ALMOST MADE IT ALL THE WAY OUT.  MY RECOVERY EFFORTS COST ME SOME CARNAGE














MADE IT OVER FIRST HUMP AND HE STILL COULDN'T DRIVE OUT.  I HAD TO BACK UP TO HIGHER GROUND TO PULL HIM THROUGH FIRST OF TWO HOLES




I HAD TO BACK THROUGH SECOND HOLE WHILE PULLING HIM THROUGH THE FIRST ONE.
















FINALLY, PICS OF THE CARNAGE.  LOOK CLOSELY UNDER THE JEEP.










I THINK MY AXLE IS A LITTLE OFF.







THANKS FOR LOOKING, AND AGAIN I AM SORRY IT TOOK ME SO LONG TO GET THESE UP.